Categories
BLOG

how to make a wooden bowl for weed

How to Make a Wooden Pipe Out of a Single Piece of Wood

Introduction: How to Make a Wooden Pipe Out of a Single Piece of Wood

In this instructable, I’ll show you how to make your own tobacco pipe out of a single piece of wood.

NOTE THAT THIS IS A TOBACCO AND SHISHA PIPE ONLY!
I WILL NOT BE HELD RESPONSIBLE FOR ANY ILLEGAL SUBSTANCES BEING SMOKED IN THIS PIPE, OR INJURY RESULTING FROM SMOKING THIS PIPE.

SMOKING IS BAD FOR YOU! DON’T DO IT! NOT FOR USE OF MINORS (UNDER 18 IS PROHIBITED)

For this project you will need:

A piece of wood about 1 inch square by about 4 inches(can be larger if desired.)

A 3/4 inch forstner bit, and faucet screen.

Belt sander for rough shaping

Natura oil(NOTE: Do NOT use any other finish but non toxic stuff. Remember you are going to be burning tobbaco in this pipe, so you don’t want to burn any other harsh chemicals)

A small drill bit no smaller than 1/8 inch or no larger than 1/4 inch.

Files and rasps for final shaping, and chisels for and detail work.

Japanese saw, or other thin kerf saw.

Clamps and a bench vise

Step 1: Boring the Holes: Bowl and Stem

Ok, for the first step you want to bore your bowl.

What you want to do is to bore your bowl, so that its deep enough to hold the tobacco, but not too deep, as the stem will be connected from the bottom of the bowl.

In the 1st image, we see the forstner bit about to bore the bowl hole. Note how I evenly spaced the hole so that the bowl walls will be even. The second image shows the bowl.

Next, you want to bore the stem hole. The placement of the stem is crucial. If you want to make a fancier stem, you can drill diagonally, but make sure that you leave a small amount around the stem, so that the heat dosnt burn your lips. You don’t want to drill the stem hole into the side of the bowl, so make sure you have good control with the drill. You can check the depth of the stem hole by inserting the bit till it hits the end of the hole. Then with your finger, place it in the drill bit and the entrance of the hole. Then move it outside the hole and cross-reference your finger position with the outside. See the diagram for more details.

Step 2: Shaping

Next, you are going to shape the pipe. Start off by cutting into the side of the bowl on all 4 sides of the piece of wood. as seen in the first image. once that’s complete, do the same for the stem end. seen in the second image.

Once your lines are cut in the stem, cut the waste off.
as seen in image 3. Note the edge of the bowl is cut to the depth of the stem lines.

Once you have the square pipe, round it off with the belt sander and the rasps. be careful not to go through the material into the stem or the bowl.

Once in a while, you will want to check for leaks. A good way of doing this it to cover the bowl with your hand, providing a seal around it. Then blow into the pipe, and if you did it right, there shouldn’t be any air escaping. if there is, just rub a little wood glue around the leak. and instead of blowing, suck in a little to get the glue down into the leak site.

Step 3: Final Shaping, and Finishing

Once you have your rounded out version, sand it down to remove and saw marks. this would be the time to add and visial flares, such as lines or grooves carved into the side of the bowl. One all that is complete, apply the finish and insert the screen. Pour a bit of finish in the bowl and tilt towards the stem to coat the inside. olive oil works well for this.

And with that, you should be done.

Be the First to Share

Did you make this project? Share it with us!

How to Make a Wooden Pipe Out of a Single Piece of Wood: In this instructable, I'll show you how to make your own tobacco pipe out of a single piece of wood. NOTE THAT THIS IS A TOBACCO AND SHISHA PIPE ONLY! I WILL NOT BE HELD RESPONSIBLE FOR ANY ILLEGAL SUBSTANCES BEING SMOKED IN THIS PIPE, OR INJURY RE…

How to make a weed pipe with wood in less than 10 minutes

If you have ever seen some of the breathtaking, hand-carved wooden pipes and wondered what it would be like to use one, then now is your chance. Though it won’t have the craftsmanship and manhours that a store-bought version will, this homemade wooden pipe is an excellent way to get a feel of the experience before making an investment, and a really fun DIY project that is perfect for keeping entertained on a cold or rainy day.

The problem with this kind of weed pipe is that it takes some special care in selecting the appropriate piece of wood, and to clean and upkeep such a porous material. Here you will find the best types of wood for smoking pipes, the kinds to stay away from, how to make one, and how to clean a wooden pipe in case you want to use your masterpiece on more than one occasion.

The best types of wood for a weed pipe

  • Briar
  • Oak
  • Cherry
  • Maple
  • Olive
  • Mesquite
  • Bogwood
  • Pear
  • Rosewood

Kinds of wood to avoid

High density woods like those that are listed above are ideal, but since heat and smoke will always take the path of least resistance, any type of wood will work in a punch, as none should catch fire from regular use. The biggest thing to watch out for is essential when using scrap pieces of wood, as anything pressured or chemical treated can and will make you sick, so be sure that your materials are pure and toxin-free.

How to make a wooden pipe for cannabis

  • Drill
  • Screen
  • Sandpaper
  • Carving knife (optional)
  • 1 fine drill bit
  • 1 larger flat-edged drill bit
  • 1 wood piece (at least one inch by three inches for the best results)

Carve the wood chunk into a shape that fits comfortably into the palm of your hand, leaving enough material to drill through without concern for breaking. If you don’t trust your carving skills or would prefer to skip this step, you can always use a regular block of wood as a pipe, it just isn’t going to have the same grip and feel.

Take sandpaper to all the edges of the wood to avoid slivers and provide a smooth and aesthetically appealing surface.

Use a narrow drill bit that is long enough to reach 2/4 of the way down your wood piece, and tunnel into the material slowly and carefully, until you are satisfied with its depth and width.

Use a flat-tipped drill bit or Dremel to create a bowl hole that aligns with the first tunnel that you’ve created. Once you break through the final layer of wood and both holes are connected, blow through the device to remove any loose bits.

Next, check the draw on your wooden pipe by sucking through the mouthpiece. If there is too much hesitation, and it is difficult to breathe through, then widen the original middle chamber before continuing.

Now you can install the screen on your brand-new weed pipe, and it is ready for use.

How to clean a wooden pipe

  • Pipe cleaner with bristles
  • Alcohol
  • Damp cloth

Run the pipe cleaner through the wooden mouthpiece until dry to dislodge any stuck or hardened pieces of ash.

Next, dip the pipe cleaner into alcohol, and force it through the mouthpiece again, pulling it back and forth several times to brush the insides of the weed pipe.

Blow through the pipe to force anything that remains towards the bowl hole.

Rinse the pipe cleaner, dip it once more in alcohol, and scrub the sides and floor of the bowl, taking care to avoid getting alcohol on the outside of the device.

When you are finished, wipe out the bowl with a damp cloth, and set the weed pipe on a paper towel to dry for at least 24 hours. That will give it enough time to allow the alcohol to completely evaporate before you use it.

How to make a Starburst weed pipe

Just when you think you’ve seen everything, along comes the Starburst weed pipe, a delicious addition to any DIY project collection.

If you have ever seen some of the breathtaking, hand-carved wooden pipes and wondered what it would be like to use one, then now is your chance. ]]>